by

Bootstrap Installation Procedure For Laminate

To laminate cabinets in your kitchen, the easiest, and most cost and time effective solution is to use self-adhesive laminate veneers. The results can be beautiful, at a much lower cost than replacing cabinets.

Materials needed:
•Screwdriver
•Hammer
•Sand Paper
•Putty
•Tack cloth
•Cut to Fit End Panels
•Wood Glue
•Finishing nails
•Self Adhesive Laminate
•Laminate Veneer
Step 1–Remove Doors, Moldings, Hardware

Open the cabinet door a little then use a screwdriver to remove the hinges. You can remove the molding using a hammer fork. Simply pry off the hinges, being gentle so as not to break the cabinets themselves. Keep hardware and screws together if you are planning to reuse the hardware. If there are loose or peeling finishes on the surfaces you plan to laminate, you should sand and clean to remove them. Use putty to fill in any scratches or large depressions. Any putty will do and usually takes about an hour to dry.

Step 2–Sand and Clean Surfaces

Use a fine, 150 grit, and sand paper and lightly scuff the surface where you plan to install the laminate. Using a tack cloth, remove all sawdust and particles from the surfaces, then clean them with a cloth dipped in a solution of water and dishwashing soap. Use the cloth barely wet, not soaking. If you have wax on your cupboards, remove it with ammonia.

Step 3–Install Cut to Fit End Panels

Cut to fit end panels are strips of veneer that come in packages 5 to 10 and are easily “cut to fit” your cabinets. Use the cut to fit pieces of plywood to cover the end panels of your cupboards. Measure, then cut the panel to size. Use wood glue and finishing nails to attach it firmly. Sand with 150 grit sandpaper and sand the edges of the plywood so that it is flush with the cabinet front. This will help the laminate to stick to your cabinets and extend the laminates lifespan.
Step 4-Install Self Adhesive Laminate to Inside Edges

Use a sharp utility knife, rotary cutters, or scissors and cut the laminate into strips. Strips allow for curvature and keep from bunching of the laminate. Cut ½ inch extra, both in length and width so that you can trim it flush to the cupboard after you install it. Cover the vertical pieces, the stiles, first, and then cover the horizontal pieces (the rails) second.
Beginning with the top of the stile, laminate the cabinets by peeling back a small portion of the backing paper. Uncover just enough of the veneer to firmly anchor the strip to on the inside frame. The top edge of the strip should be placed so it is square with the top of the opening. As you peel off the backing slowly, press lightly and smoothly on the veneer and keep it aligned properly. It is nearly impossible to move the veneer after it is applied, so be sure to do it right the first time. After doing the inside stiles, do inside of the rails. Use a knife to trim the inside edges even.
Step 5-Apply Veneer to Face Frame

Beginning with the stiles, once again line the veneer up carefully. Anchor the top, and make sure it is flush and square. Then, laminate cabinets by carefully installing the veneer on the face of the cabinet. Keep an even overlap on both sides of the stile. If even one veneer is uneven, it will ruin the entire cabinet. Repeat for other stile, then apply the laminate on the rails in the same way.

Step 6-Trim

Carefully use a sharp utility knife to trip the excess and overlap from the openings. Make sure you have a steady hand at this point.
Congratulations, you laminated your cabinets! It is a simple project that adds a little flair to any room with cabinetry.

Here's what I tried:
sudo ng new angularmdbpro --style=scss
which created the project successfully

If your FileNet P8 domain uses multiple non-managed application servers, then complete this procedure only on the initial server. You use a copy of the same EAR file with the bootstrap settings on all the servers. Browse Armstrong Flooring's F-5061 installation guide, covering each step of the installation process. Thank you for choosing to explore Audacity water resistant laminate! You are now leaving the Armstrong Flooring website and being redirected to a partner site AudacityFlooring.com. Bootstrap – installation process: CLI ADE-OS configuration details – continued Bootstrap – after installation use show run command to see ADE OS configuration Bootstrap – after installation use: node1/admin#show application status ise command to verify services that are running.

Bootstrap Installation Procedure For Laminate Floors

I cd'd into the angularmdbpro directory and set the directory and all sub directories wide open, 777 (read and write)

I ran:
sudo npm install git+https://oauth2:@git.mdbootstrap.com/mdb/angular/ng-pro.git —save
which failed because of your typo '-save', it needs to be '--save'. Could you PLEASE UPDATE THIS. A lot of us are new to Angular and when we copy and paste from your documentation it really messes us up.

I ran:

sudo npm install git+https://oauth2:@git.mdbootstrap.com/mdb/angular/ng-pro.git --save and I got the following error:

At this point I saw the permissions error pointing to /Users/rich/.npm/cacache/tmp/git-clone....

So I set /Users/rich/.npm/cacache/tmp directory wide open and tried running the sudo npm install git+https://oauth2:@git.mdbootstrap.com/mdb/angular/ng-pro.git --save and I got the same error as the first time I ran it.

Is something on your .git system/files resetting my permissions? I opened everything wide open (which I don't feel good about, btw as I'll need to do this on client systems who probably won't let me do it, and it rightfully so).

Anyway, for grins I tried ng serve, and I got the following error:

For

Guys I really want to use your software but obviously it has to install. What next? I'm just not that advanced with Angular so just about anything else you suggest I'll need specific code for. Also, I'm running out of time!!!

Bootstrap Installation Procedure For Laminated

Bootstrap

Thanks,

Rich

Damian Gemzastaff commented 2 years ago

Dear Rich, firstly, please, if you pasting here some code, please be sure to remove your's personal token for our product. If you paste here your's token, someone could steal it - it won't be good. Secondly, after installation of fresh angular project, before you ran to it's directory, please use chmod -R 777 your-angular-project. It will change permissions to 777 recursively. After this chmod, you can cd to your's project, and type sudo npm install git+https... Did you tried to remove your's angular and cli globally and install the latest version with @latest ? Maybe that's the case that your's angular version isn't compatible with our MDB? Please try my advices. If it won't work, we'll do something else. Best Regards, Damian

rich@cfsnap.compro commented 2 years ago

Bootstrap Installation Procedure For Laminate Floor

Do you guys have a system/minimum requirements section anywhere for MDB Angular Pro? Procedure

Damian Gemzastaff commented 2 years ago

Rich, our product is web development framework. It should works on every device, cause it's require only a browser, and environment like node...